How to Replace a Kitchen Faucet
Please Select Username to appear on public gook of the site like community and recipe comments. Sign up today for FREE and become part of Hook up faucet Family Handyman community of DIYers. Fixing a toilet Electrical Organizing Cleaning Plumbing Pub Shed. The toughest part of replacing a kitchen faucet is removing the old one.
Unexpected problems always pop up—corroded pipes, difficult-to-reach nuts and poor access to fittings. Barring unforeseen problems, you could be washing up under the faucet in an hour or so. In this article walk you through a basic replacement process and tell you how to get through those tough parts. Disconnect the drain lines and P-traps if they block your access to the faucet and water supply pipes. Place a fzucet or coffee can under the P-trap to dump residual water after you pull it free.
If the faucet still drips, install new ones. But if not, buy whichever valve type is compatible with your pipes. Next, measure the existing supply tubes and buy new stainless steel—sleeved supply tubes Photo 9. This weird little wrench is made fsucet for removing and installing those hard-to-reach fasteners that clamp older faucet assemblies to the sink. Newer faucets have plastic Wing-Nuts that can usually be loosened and tightened by hand. If you need to remove drain lines to access the faucet, get a pipe wrench or slip-joint pliers Photo 1.
For cutting copper tubes, buy a conventional tubing cutter. But if your copper supply lines are within a few inches of the back of the cabinet, buy a special mini tube cutter Photo 3. Before disconnecting the drain lines, take a Polaroid snapshot or make a sketch of the layout to help you put it all back together. Plan on replacing your faucet during store hours.
Prop up a scrap of plywood on some 1-qt. Otherwise, the edge of the cabinet would be digging into your back. Unplug the garbage disposer, or shut the circuit breaker in the main service panel if the disposer is directly wired. Disconnect the dishwasher discharge line and place a 1-gal. Release the disposer by tapping the retaining ring with a hammer in a counterclockwise direction.
Shut off the water below the sink if you have valves, or shut off the main water supply valve if your old faucet is plumbed directly without valves. Open the kitchen faucet and another lower faucet to bleed off any pressure and to drain the water. Reach up behind the sink, fit the basin wrench jaws onto the tailpiece nuts and turn counterclockwise to loosen. Then disconnect the spray nozzle hose, remove the faucet and clean the sink area under the old faucet flange.
After you pull out all of the cleansers, buckets and old vases from under the sink, go ahead and lie under there and see if you can easily access the faucet. If so, go right to Photo 3. Most likely, the main obstacles will be the hook up faucet and P-traps that drain the sinks. After you remove them, throw all the parts in a box for matching them exactly at the store later.
Sometimes a garbage disposer can be a lb. Unplug it and pull it out of the cabinet to get it out of the way. The first step in removing the old faucet is to disconnect hook up faucet water supply lines Photo 3. Make sure hopk valves are closed before turning the water back on to the house. Once the water lines are disconnected, use the basin wrench to loosen the old faucet and remove it Photo 4.
Try soaking the threads with penetrating oil and try again. Loosen the screws on the bottom of the sink rim for a clamp-down sink, or cut the caulk between a drop-in sink and countertop with a utility knife and lift out the sink. If jp replacing the kitchen sink along with a new faucet, install the faucet before setting the sink into the countertop.
Follow any manufacturer's preassembly instructions and place the optional flange see Photo 8 over the faucet opening. Finger-tighten the flange nuts underneath the sink and check the alignment of the flange, faucet and sink hole from above. Then slip on the faucet washer, and thread on and tighten the faucet-mounting nut from below, gently spreading the faucet supply tubes if necessary to gain tool clearance sometimes manufacturers provide a special tool for this. Hand-tighten, then hook up faucet up the flange nuts with an open-end wrench.
You can only fajcet the wrench about a one-sixth revolution at a time. Thread the spray nozzle line through the faucet body, then thread the spray hose hook up faucet onto the faucet supply tube and tighten it. Tighten the new valves onto the supply tubes and mark the feeder lines just above the compression nuts hook up faucet the valves for hook up faucet. Clean the copper tubing with fine sandpaper, then slip the nut, compression ring and valve body over the pipe and tighten.
Close the valve, turn on the main water valve and check for leaks. Place fauct bucket under the hpok and turn the faucet on to check for leaks. Reassemble the garbage disposer, P-traps and drain lines. Follow the manufacturer's directions to mount the new faucet, then remount the sink with the new faucet and hook up the water lines as we show. With most faucets, only three of the fakcet holes are covered, so you'll either need to get a blank insert or use the extra hole for a liquid soap or instant hot water dispenser.
Plan to do the installation while you're under the sink with everything torn apart. Some even come with a lifetime warranty. Avoid last-minute shopping trips by having all hoom materials ready ahead of time. Get timely DIY projects for your home and yard delivered right to your inbox every week! Please enter valid E-Mail Address. Email or username is incorrect. Please enter a valid username.
Username cannot contain spaces or special characters. Please enter a password. Log In Hook up faucet us Cancel. Don't have an account yet? Magazine Give a gift Shop. Get DIY tips in your inbox. Home Skills Plumbing How to Replace a Kitchen Faucet How to Replace a Kitchen Hook up faucet Lots of useful tips hook up faucet step-by-step advice on how to install a new kitchen faucet, including how to avoid common problems.